Manufacturer: Hughes, Manufacturer Part Number: H45GSP-2HFor cold climates with a minimum ambient operating temperature of -4 °F (-20 °C) or above—trace tape heating with polyethylene jacket and polyurethane foam insulation improve frost protection and strength Covered acrylic-capped ABS eye/face wash protects the bowl and eyewash diffusers from dust and debris—no dust covers needed Diffusers fitted with fine mesh strainers and a flow controller provide a gentle flow of aerated water and prevent further injury to the eyes Includes a separate 10 x 12-in (254 x 305-mm) universal eyewash sign for enhanced visibility, as well as an inspection record tag for recording test and service history Meets ANSI and EN 15154 standards and supports OSHA requirements. This freeze protected and insulated eye/face wash is intended for use where there is a possibility of the water freezing due to extreme cold climates. Pedestal-mounted eye/face wash unit, designed at ANSI-compliant height, is generally located in open areas away from walls. These freeze protected models are trace-tape heated and insulated, suitable for use in both Class 1 Division 2 hazardous areas, as well as non-hazardous areas. Made of durable, corrosion-resistant acrylic capped ABS, the eye/face wash incorporates an integral lid connected to the water valve for automatic operation—activate by simply pulling down the lid. Easy-to-reach flow regulator valve positioned on side of bowl adjusts to suit the severity of the accident. Solid construction using stainless steel pipework for improved corrosion resistance. Add optional foot treadle for a secondary means of activation. Some assembly may be required. Electrical supply: 240V Single Phase, 60/50HzSPECIFICATIONSEye/Face Wash Bowl Material: Acrylic-Capped ABS PlasticActivation: Pull Down on LidMaterial Specifications: Polyurethane foam insulation with a medium density polyethylene impact resistant outer casing, Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.

Manufacturer: Hughes, Manufacturer Part Number: H45GSP-1HFor cold climates with a minimum ambient operating temperature of -4 °F (-20 °C) or above—trace tape heating with polyethylene jacket and polyurethane foam insulation improve frost protection and strength Covered acrylic-capped ABS eye/face wash protects the bowl and eyewash diffusers from dust and debris—no dust covers needed Diffusers fitted with fine mesh strainers and a flow controller provide a gentle flow of aerated water and prevent further injury to the eyes Includes a separate 10 x 12-in (254 x 305-mm) universal eyewash sign for enhanced visibility, as well as an inspection record tag for recording test and service history Meets ANSI and EN 15154 standards and supports OSHA requirements. This freeze protected and insulated eye/face wash is intended for use where there is a possibility of the water freezing due to extreme cold climates. Pedestal-mounted eye/face wash unit, designed at ANSI-compliant height, is generally located in open areas away from walls. These freeze protected models are trace-tape heated and insulated, suitable for use in both Class 1 Division 2 hazardous areas, as well as non-hazardous areas. Made of durable, corrosion-resistant acrylic capped ABS, the eye/face wash incorporates an integral lid connected to the water valve for automatic operation—activate by simply pulling down the lid. Easy-to-reach flow regulator valve positioned on side of bowl adjusts to suit the severity of the accident. Solid construction using stainless steel pipework for improved corrosion resistance. Add optional foot treadle for a secondary means of activation. Some assembly may be required. Electrical supply: 120V Single Phase, 60/50HzSPECIFICATIONSEye/Face Wash Bowl Material: Acrylic-Capped ABS PlasticActivation: Pull Down on LidMaterial Specifications: Polyurethane foam insulation with a medium density polyethylene impact resistant outer casing, Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.

Manufacturer: Hughes, Manufacturer Part Number: H45GP-2HFor cold climates with a minimum ambient operating temperature of -4 °F (-20 °C) or above—trace tape heating with polyethylene jacket and polyurethane foam insulation improve frost protection and strength Covered acrylic-capped ABS eye/face wash protects the bowl and eyewash diffusers from dust and debris—no dust covers needed Diffusers fitted with fine mesh strainers and a flow controller provide a gentle flow of aerated water and prevent further injury to the eyes Includes a separate 10 x 12-in (254 x 305-mm) universal eyewash sign for enhanced visibility, as well as an inspection record tag for recording test and service history Meets ANSI and EN 15154 standards and supports OSHA requirements. This freeze protected and insulated eye/face wash is intended for use where there is a possibility of the water freezing due to extreme cold climates. Pedestal-mounted eye/face wash unit, designed at ANSI-compliant height, is generally located in open areas away from walls. These freeze protected models are trace-tape heated and insulated, suitable for use in both Class 1 Division 2 hazardous areas, as well as non-hazardous areas. Made of durable, corrosion-resistant acrylic capped ABS, the eye/face wash incorporates an integral lid connected to the water valve for automatic operation—activate by simply pulling down the lid. Easy-to-reach flow regulator valve positioned on side of bowl adjusts to suit the severity of the accident. Solid construction using galvanized mild steel pipework. Add optional foot treadle for a secondary means of activation. Some assembly may be required. Electrical supply: 240V Single Phase, 60/50HzSPECIFICATIONSEye/Face Wash Bowl Material: Acrylic-Capped ABS PlasticActivation: Pull Down on LidMaterial Specifications: Polyurethane foam insulation with a medium density polyethylene impact resistant outer casing, Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.

Manufacturer: Hughes, Manufacturer Part Number: H45GP-1HFor cold climates with a minimum ambient operating temperature of -4 °F (-20 °C) or above—trace tape heating with polyethylene jacket and polyurethane foam insulation improve frost protection and strength Covered acrylic-capped ABS eye/face wash protects the bowl and eyewash diffusers from dust and debris—no dust covers needed Diffusers fitted with fine mesh strainers and a flow controller provide a gentle flow of aerated water and prevent further injury to the eyes Includes a separate 10 x 12-in (254 x 305-mm) universal eyewash sign for enhanced visibility, as well as an inspection record tag for recording test and service history Meets ANSI and EN 15154 standards and supports OSHA requirements. This freeze protected and insulated eye/face wash is intended for use where there is a possibility of the water freezing due to extreme cold climates. Pedestal-mounted eye/face wash unit, designed at ANSI-compliant height, is generally located in open areas away from walls. These freeze protected models are trace-tape heated and insulated, suitable for use in both Class 1 Division 2 hazardous areas, as well as non-hazardous areas. Made of durable, corrosion-resistant acrylic capped ABS, the eye/face wash incorporates an integral lid connected to the water valve for automatic operation—activate by simply pulling down the lid. Easy-to-reach flow regulator valve positioned on side of bowl adjusts to suit the severity of the accident. Solid construction using galvanized mild steel pipework. Add optional foot treadle for a secondary means of activation. Some assembly may be required. Electrical supply: 120V Single Phase, 60/50HzSPECIFICATIONSEye/Face Wash Bowl Material: Acrylic-Capped ABS PlasticActivation: Pull Down on LidMaterial Specifications: Polyurethane foam insulation with a medium density polyethylene impact resistant outer casing, Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.

Manufacturer: Hughes, Manufacturer Part Number: 15GEWCost-effective, ANSI-compliant solution for locations that are unsuitable for fixed installations or those without access to a plumbed-in water supply. 15 US gallon (56.8 liter) stainless steel pressure vessel with built in carrying handles, provides emergency eye washing for up to 15 minutes Pop-off dust covers and push lever operation for ease of use Pressure gauge and dual action safety valve prevent over pressurization and allow the user to vent the cylinder for cleaning and maintenance Includes ANSI-compliant identification sign on activation lever and inspection tag for recording test and service history Use integral 1/2-in (F) NPT connection to attach optional drench hose OPT50 for decontamination of body parts subjected to minor exposureSPECIFICATIONSActivation: Push PlateMaterial Specifications: Body: Stainless Steel, Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.

Manufacturer: Hughes, Manufacturer Part Number: 16GFEWPSelf-Contained 16-Gallon Gravity-Fed Eyewash Station. Suitable wherever continuous water isn't available—no plumbing needed. The gravity-fed eyewash supplies a continuous, controlled flow that exceeds the ANSI Z358.1 standard of 1.5 LPM (0.4 GPM) for 15 minutes, providing a reliable safety solution no matter where you are located. Portable design with carrying handles and concealed mounting bracket make moving and relocating easy Can be wall mounted or used on a bench or tabletop High-visibility color is easy to identify in emergency situations Simple to use with pull-down activation handle Easy to maintain—wide fill opening enables quick inspection, cleaning and filling Meets ANSI Z358.1 and EN15154 requirementsSPECIFICATIONSActivation: Pull Handle

Manufacturer: Bradley, Manufacturer Part Number: S59-3400Bradley Navigator Thermostatic Mixing Valve, designed for use in commercial applications. Valve designed for master hot water distribution. High/Low type valve is designed to control water temperature during periods of both high and low demand. Powerful liquid filled thermostat with 10 year warranty insures constant outlet temperature. Temperature range 90–120 degrees F. Certified to ASSE 1017. Certified to cUPC standards. Certified to CSA standards. Rough brass finish. 384 GPM @ PSI. Incoming 3in. NPT connections, outlet is 3in. NPT, Dial thermometer. Maximum operating pressure of 125 PSI. Maximum inlet temperature of 200 degrees F. Minimum temperature differential of 15 degrees F between incoming hot water temperature and valve set point. Manufactures limited warranty.

Manufacturer: Bradley, Manufacturer Part Number: S45-2465Frequency Lav, Triple Station (High On Left And Right). 1200 Series Cs Faucet, Centershank. Accommodates Up To 3 Users At A Time. Thermostatic Mixing Valve With Adjustable Set Point. Valve Compensates For Pressure And Temperature Changes. Trap Cover Coal. Riverstone–Designer Color. Terreon Solid Surface Material Resistant To Chemicals, Stains, Burns And Impact. Surface Damage Can Easily Be Repaired. Complies With ADA Guidelines. Complies With TAS. Certified By IAPMO To UPC & cUPC Regulations. Certified By NAHB To Comply With ANSI Z124.3, Z124.6 & ICPA. Greenguard Certified. Manufacturers Limited Warranty.

Manufacturer: Bradley, Manufacturer Part Number: S19-324EWall or Fixture Mounted General Area Emergency Signaling System. Indoor and Outdoor Installation. NEMA 4X Rated. For Use With Eye or Eye/Face Wash Units. Double Pole Double Throw (DPDT) Flow Switch in Brass Construction, 1/2" NPT Supply. Remote Location Hookup Possible via Contacts in Flow Switch and/or On Control Board. Automatic, Audible, and Visual Alarm. Minimum 2.4 GPM Flow Required. 6 Foot Cord. Universal Voltage: 90-264 AC, 50-60 Hz. Amber Signal Light and Piezo Fast Beep Horn Sound Activate When Fixture is Used. Silence Switch with Automatic Reset Included. Central Control Board Powers All Options and Runs on Safe 24 V System. UL Listed.

Manufacturer: Bradley, Manufacturer Part Number: S19-324EGWall or Fixture Mounted General Area Emergency Signaling System. Indoor and Outdoor Installation. NEMA 4X Rated. For Use With Eye or Eye/Face Wash Units. Double Pole Double Throw (DPDT) Flow Switch in Brass Construction, 1/2" NPT Supply. Remote Location Hookup Possible via Contacts in Flow Switch and/or On Control Board. Automatic, Audible, and Visual Alarm. Minimum 2.4 GPM Flow Required. 6 Foot Cord. Universal Voltage: 90-264 AC, 50-60 Hz. Amber Signal Light and Piezo Fast Beep Horn Sound Activate When Fixture is Used. Silence Switch with Automatic Reset and Green Beacon Light Included. Central Control Board Powers All Options and Runs on Safe 24 V System. UL Listed.

Manufacturer: Bradley, Manufacturer Part Number: S19-324EGWWall or Fixture Mounted General Area Emergency Signaling System. Indoor and Outdoor Installation. NEMA 4X Rated. For Use With Eye or Eye/Face Wash Units. Double Pole Double Throw (DPDT) Flow Switch in Brass Construction, 1/2" NPT Supply. Remote Location Hookup Possible via Contacts in Flow Switch and/or On Control Board. Automatic, Audible, and Visual Alarm. Minimum 2.4 GPM Flow Required. 6 Foot Cord. Universal Voltage: 90-264 AC, 50-60 Hz. Amber Signal Light and Piezo Fast Beep Horn Sound Activate When Fixture is Used. Silence Switch with Automatic Reset, Green Beacon Light, and White Area Light Included. Central Control Board Powers All Options and Runs on Safe 24 V System. UL Listed.

Manufacturer: Bradley, Manufacturer Part Number: S59-3045HBradley Navigator Thermostatic Mixing Valve, designed for use in commercial applications. Lead free design, third party certified, contains less than 0.25% lead on wetted surfaces. Valve designed for master hot water distribution. High/Low type valve is designed to control water temperature during periods of both high and low demand. Powerful liquid filled thermostat with 10 year warranty insures constant outlet temperature. Temperature range 90–120 degrees F. Certified to ASSE 1017. Certified to cUPC standards. Certified to CSA standards. Certified by IAPMO to meet lead free plumbing laws. Rough bronze finish. 47 GPM @ 45 PSI. Incoming 3/4in. NPT connections, outlet is 1in. NPT. Dial thermometer. Maximum operating pressure of 125 PSI. Maximum inlet temperature of 200 degrees F. Minimum temperature differential of 15 degrees F between incoming hot water temperature and valve set point. Universal Mounting Capability. Manufactures limited warranty.

Manufacturer: Bradley, Manufacturer Part Number: S19-323EWall or Fixture Mounted General Area Emergency Signaling System. Indoor and Outdoor Installation. NEMA 3R Rated. For Use With Eye or Eye/Face Wash Units. Double Pole Double Throw (DPDT) Flow Switch in Brass Construction, 1/2" NPT Supply. Remote Location Hookup Possible via Contacts in Flow Switch or On Control Board. Automatic, Audible, and Visual Alarm. Minimum 2.4 GPM Flow Required. 6 Foot Cord. Universal Voltage: 90-264 AC, 50-60 Hz. Amber Signal Light and Piezo Fast Beep Horn Sound Activate When Fixture is Used. Central Control Board Powers All Options and Runs on Safe 24 V System. UL Listed.

Manufacturer: Bradley, Manufacturer Part Number: S45-2466Frequency Lav, Triple Station (Low On Left And Right). 1200 Series Cs Faucet, Centershank. Accommodates Up To 3 Users At A Time. Thermostatic Mixing Valve With Adjustable Set Point. Valve Compensates For Pressure And Temperature Changes. Trap Cover Coal. Riverstone–Designer Color. Terreon Solid Surface Material Resistant To Chemicals, Stains, Burns And Impact. Surface Damage Can Easily Be Repaired. Complies With ADA Guidelines. Complies With TAS. Certified By IAPMO To UPC & cUPC Regulations. Certified By NAHB To Comply With ANSI Z124.3, Z124.6 & ICPA. Greenguard Certified. Manufacturers Limited Warranty.

Manufacturer: Hughes, Manufacturer Part Number: L85GSPEasy-to-clean powder coated stainless steel bowl for excellent corrosion resistance Pop-off dust covers protect the twin spray nozzles from contaminants, these are lifted off by the water jets upon operation via the push plate Fine mesh strainers and an individual flow controller provide a gentle flow of aerated water and prevent further injury to the eyes High-performance quarter-turn ball valves made of 316L stainless steel endure the harshest environments and site conditions— low operating torque offers reliable, easy on/off operation Includes a separate 10 x 12-in (254 x 305-mm) universal eye wash sign for enhanced visibility, as well as an inspection record tag for recording test and service history Ideal for laboratories, schools and general light duty indoor use, this pedestal mounted eye/face wash unit meets ANSI Z358.1 and EN 15154 standards, and supports OSHA requirements.SPECIFICATIONSEye/Face Wash Bowl Material: Green Powder-Coated Stainless SteelActivation: Push PlateMaterial Specifications: Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.

Manufacturer: Bradley, Manufacturer Part Number: S45-2463Frequency Lav, Double Station (High On Left). 1200 Series Cs Faucet, Centershank. Accommodates Up To 2 Users At A Time. Thermostatic Mixing Valve With Adjustable Set Point. Valve Compensates For Pressure And Temperature Changes. Trap Cover Coal. Riverstone–Designer Color. Terreon Solid Surface Material Resistant To Chemicals, Stains, Burns And Impact. Surface Damage Can Easily Be Repaired. Complies With ADA Guidelines. Complies With TAS. Certified By IAPMO To UPC & cUPC Regulations. Certified By NAHB To Comply With ANSI Z124.3, Z124.6 & ICPA. Greenguard Certified. Manufacturers Limited Warranty.

Manufacturer: Bradley, Manufacturer Part Number: S45-2464Frequency Lav, Double Station (Low On Left). 1200 Series Cs Faucet, Centershank. Accommodates Up To 2 Users At A Time. Thermostatic Mixing Valve With Adjustable Set Point. Valve Compensates For Pressure And Temperature Changes. Trap Cover Coal. Riverstone–Designer Color. Terreon Solid Surface Material Resistant To Chemicals, Stains, Burns And Impact. Surface Damage Can Easily Be Repaired. Complies With ADA Guidelines. Complies With TAS. Certified By IAPMO To UPC & cUPC Regulations. Certified By NAHB To Comply With ANSI Z124.3, Z124.6 & ICPA. Greenguard Certified. Manufacturers Limited Warranty.

Manufacturer: Hughes, Manufacturer Part Number: L85GSEasy-to-clean powder coated stainless steel bowl for excellent corrosion resistance Pop-off dust covers protect the twin spray nozzles from contaminants, these are lifted off by the water jets upon operation via the push plate Fine mesh strainers and an individual flow controller provide a gentle flow of aerated water and prevent further injury to the eyes High-performance quarter-turn ball valves made of 316L stainless steel endure the harshest environments and site conditions— low operating torque offers reliable, easy on/off operation Includes a separate 10 x 12-in (254 x 305-mm) universal eye wash sign for enhanced visibility, as well as an inspection record tag for recording test and service history Ideal for laboratories, schools and general light duty indoor use, this wall mounted eye/face wash unit meets ANSI Z358.1 and EN 15154 standards, and supports OSHA requirements.SPECIFICATIONSEye/Face Wash Bowl Material: Green Powder-Coated Stainless SteelActivation: Push PlateMaterial Specifications: Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.

Manufacturer: Bradley, Manufacturer Part Number: S19-2300NAVIGATOR THERMOSTATIC MIXING VALVE FOR EYEWASHES, 103 GPM @ 30 PSI, UNIVERSAL MOUNTING, DIAL THERMOMETER, 1 1/4" NPT HOT/COLD WATER SUPPLY CONNECTIONS RELIABLE LIQUID FILLED THERMOSTAT, COLD WATER BYPASS, HOT WATER SHUT–OFF, SINGLE VALVE DESIGN, LEAD FREE. Kit: NO.

Manufacturer: Hughes, Manufacturer Part Number: L85GSTEasy-to-clean powder coated stainless steel bowl for excellent corrosion resistance Pop-off dust covers protect the twin spray nozzles from contaminants, these are lifted off by the water jets upon operation via the push plate Fine mesh strainers and an individual flow controller provide a gentle flow of aerated water and prevent further injury to the eyes High-performance quarter-turn ball valves made of 316L stainless steel endure the harshest environments and site conditions— low operating torque offers reliable, easy on/off operation Includes a separate 10 x 12-in (254 x 305-mm) universal eye wash sign for enhanced visibility, as well as an inspection record tag for recording test and service history Ideal for laboratories, schools and general light duty indoor use, this eye/face wash unit mounts flush to a table or bench, meets ANSI Z358.1 and EN 15154 standards, and supports OSHA requirements.SPECIFICATIONSEye/Face Wash Bowl Material: Green Powder-Coated Stainless SteelActivation: Push PlateMaterial Specifications: Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.

Manufacturer: Hughes, Manufacturer Part Number: 45GSPCovered bowl ensures that the nozzles and bowl remain clean and free from contamination at all times—no dust covers needed Durable, corrosion-resistant acrylic capped ABS construction Twin aerated diffusers with fine mesh strainers and an individual flow controller provide a soft, scrubbing action to the eyes and face Includes a separate 10 x 12-in (254 x 305-mm) universal eye wash sign for enhanced visibility, as well as an inspection record tag for recording service and test history Meets ANSI Z358.1 and EN 15154 standards, supports OSHA requirements Wall-mounted eye/face wash with high, ANSI-compliant flow rate is suitable for use in all applications not subject to the possibility of freezing or overheating. Solid construction using stainless steel pipework for added improved corrosion resistance. The eye/face wash incorporates an integral lid connected to the water valve for automatic operation—activate by simply pulling down the lid. Easy-to-reach flow regulator valve positioned on side of bowl adjusts to suit the severity of the accident. Add optional foot treadle for a secondary means of activation. Some assembly may be required.SPECIFICATIONSEye/Face Wash Bowl Material: White Acrylic-Capped ABS PlasticActivation: Pull Down on LidMaterial Specifications: Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.

Manufacturer: Hughes, Manufacturer Part Number: 85GPTwin spray nozzles protected by dust covers that pop-off when eye wash is activated Diffusers fitted with fine mesh strainers and a flow controller provide a gentle flow of aerated water and prevent further injury to the eyes High-performance quarter-turn ball valves made of 316L stainless steel endure the harshest environments and site conditions— low operating torque offers reliable, easy on/off operation Includes a separate 10 x 12-in (254 x 305-mm) universal eyewash sign for enhanced visibility, as well as an inspection record tag for recording service and test history Meets ANSI and EN 15154 standards and supports OSHA requirements Pedestal-mounted, open stainless steel bowl eye/face wash unit, designed at ANSI-compliant height, is generally located in open areas away from walls. Suitable for use in all applications not subject to the possibility of freezing or overheating. The system features a specially designed valve that includes an integral, heavy-duty stainless steel stop-plate to handle rough operation without failure. Solid construction using galvanized mild steel pipework. Easy activation—highly visible red push plate with universal hand and eye wash sign. Add optional foot treadle for a secondary means of activation. Some assembly may be required.SPECIFICATIONSEye/Face Wash Bowl Material: Stainless SteelActivation: Push PlateMaterial Specifications: Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.

Manufacturer: Hughes, Manufacturer Part Number: 85GSPTwin spray nozzles protected by dust covers that pop-off when eye wash is activated Diffusers fitted with fine mesh strainers and a flow controller provide a gentle flow of aerated water and prevent further injury to the eyes High-performance quarter-turn ball valves made of 316L stainless steel endure the harshest environments and site conditions— low operating torque offers reliable, easy on/off operation Includes a separate 10 x 12-in (254 x 305-mm) universal eyewash sign for enhanced visibility, as well as an inspection record tag for recording service and test history Meets ANSI and EN 15154 standards and supports OSHA requirements Pedestal-mounted, open stainless steel bowl eye/face wash unit, designed at ANSI-compliant height, is generally located in open areas away from walls. The system features a specially designed valve that includes an integral, heavy-duty stainless steel stop-plate to handle rough operation without failure. Suitable for use in all applications not subject to the possibility of freezing or overheating. Solid construction using stainless steel pipework for improved corrosion resistance. Easy activation—highly visible red push plate with universal hand and eye wash sign. Add optional foot treadle for a secondary means of activation. Some assembly may be required.SPECIFICATIONSEye/Face Wash Bowl Material: Stainless SteelActivation: Push PlateMaterial Specifications: Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.

Manufacturer: Hughes, Manufacturer Part Number: 75GSPTwin spray nozzles protected by dust covers that pop-off when eye wash is activated Diffusers fitted with fine mesh strainers and a flow controller provide a gentle flow of aerated water and prevent further injury to the eyes High-performance quarter-turn ball valves made of 316L stainless steel endure the harshest environments and site conditions— low operating torque offers reliable, easy on/off operation Includes a separate 10 x 12-in (254 x 305-mm) universal eyewash sign for enhanced visibility, as well as an inspection record tag for recording service and test history Meets ANSI and EN 15154 standards and supports OSHA requirements Pedestal-mounted, open ABS plastic bowl eye/face wash unit, designed at ANSI-compliant height, is generally located in open areas away from walls. Suitable for use in all applications not subject to the possibility of freezing or overheating. The system features a specially designed valve that includes an integral, heavy-duty stainless steel stop-plate to handle rough operation without failure. Solid construction using stainless steel pipework for improved corrosion resistance. Easy activation—highly visible red push plate with universal hand and eye wash sign. Add optional foot treadle for a secondary means of activation. Some assembly may be required.SPECIFICATIONSEye/Face Wash Bowl Material: Yellow ABS PlasticActivation: Push PlateMaterial Specifications: Eye/facewash diffusers: Chrome plated brass with stainless steel mesh.