Ramps and Dock Plates

Manufacturer: Vestil, Manufacturer Part Number: TS-15-7260Constructed of high strength (55,000 psi) steel for long life. Beveled edges on both ends permit smooth entry and exit. Deck is diamond plated for safe, efficient use. Welded safety curbs for maximum strength. Locking legs minimize ramp movement and are uneven to allow the dockboard to sit canted for easier floor pickup by forklifts. Standard with leverlift for quick portability with fork truck. When using three wheeled fork trucks, select capacity +20% due to concentrated load on center of board. Optional accessories: lifting chains, span locks, span pins/holes and removable pickup loops. Manufactured in compliance with OSHA.SPECIFICATIONS15,000 lbs Capacity60" x 72" x 15.375" - 597 lbs.

Manufacturer: Vestil, Manufacturer Part Number: FM-2072The Edge-O-Dock leveler permanently attaches to face of dock. It is recommended for docks to be at least forty-eight (48) inches high. When the trailer departs, the lip drops automatically behind the face of the bumpers. Concrete recess is not required. It comes complete with bumpers and installation instructions. Standard Ramping is twenty-seven (29) inches, with a thirty-six (36-5/8) inch long ramping length available for smaller grade. A steel dock edge, or approach ramp is required for proper installation. The Mechanical Edge-O-Dock is operated by placing the actuation handle into the pocket of the inner lip and pulling down toward the floor. The operator then pushes the handle forward until the lip rests on the truck bed. As the trailer departs, the lip retracts behind the bumper face automatically.

Manufacturer: Vestil, Manufacturer Part Number: TS-15-7248Constructed of high strength (55,000 psi) steel for long life. Beveled edges on both ends permit smooth entry and exit. Deck is diamond plated for safe, efficient use. Welded safety curbs for maximum strength. Locking legs minimize ramp movement and are uneven to allow the dockboard to sit canted for easier floor pickup by forklifts. Standard with leverlift for quick portability with fork truck. When using three wheeled fork trucks, select capacity +20% due to concentrated load on center of board. Optional accessories: lifting chains, span locks, span pins/holes and removable pickup loops. Manufactured in compliance with OSHA. SPECIFICATIONS15,000 lbs Capacity48" x 72" x 12.375" - 496 lbs.

Manufacturer: Vestil, Manufacturer Part Number: FM-2066The Edge-O-Dock leveler permanently attaches to face of dock. It is recommended for docks to be at least forty-eight (48) inches high. When the trailer departs, the lip drops automatically behind the face of the bumpers. Concrete recess is not required. It comes complete with bumpers and installation instructions. Standard Ramping is twenty-seven (29) inches, with a thirty-six (36-5/8) inch long ramping length available for smaller grade. A steel dock edge, or approach ramp is required for proper installation. The Mechanical Edge-O-Dock is operated by placing the actuation handle into the pocket of the inner lip and pulling down toward the floor. The operator then pushes the handle forward until the lip rests on the truck bed. As the trailer departs, the lip retracts behind the bumper face automatically.

Manufacturer: Vestil, Manufacturer Part Number: E-4860Economical way to speed up truck loading and unloading. Spans the opening between dock and trailer to allow pallet or hand trucks along with people to safely move in and out of the trailer. Constructed of high strength, lightweight aluminum alloy non–skid tread plate. Handles are located on each side for portability. Locking legs for OSHA Compliance. The bend or crown is 11° and located 9" from edge of dockplate. Not for use with fork trucks. SPECIFICATIONS1,800 lbs Capacity60" x 48" x 12.5" - 128 lbs.

Manufacturer: Vestil, Manufacturer Part Number: SCR-84Uniform Capacity (lbs.): 15000 – The Heavy Duty Steel Container Ramp facilitates easy loading/unloading of shipping containers when placed on ground level. Hinged flip–over bridge allows for easy transportation and compact storage. Tapered lip provides smooth transition into container at various heights. Built in fork pockets in base for convenient fork truck positioning.

Manufacturer: Vestil, Manufacturer Part Number: CRS-6060-15A CRS container ramp is the perfect asset for loading and unloading products over uneven surfaces. The steel construction is long lasting and durable throughout harsh working conditions and inclement weather. During those adverse atmospheres the raised tread plate platform surface enables the user to have sure footing and minimize worker injury during use. The beveled edges on both ends allow smooth entry/exit by limiting the surface of height difference during transition. Side curbs also play a large role in the user safety by helping to maintain a safe alignment of goods as they pass from one area to another. Pick-up chains are included for simple transference of unit to different areas around the workplace. A range of large capacity designs are available to best suit your specific needs. MFG Part# CRS-6060-15

Manufacturer: Vestil, Manufacturer Part Number: VTR-6-14-14Uniform Capacity (lbs.): 5500, Working Height Minimum (in.): 25–1/2, Working Height Maximum (in.): 36–1/2, Usable Width (in.): 14, Curb Height (in.): 1–1/4 – The Aluminum Vehicle Twin Ramps provide a safe means for driving vans, pick–up trucks and some passenger vehicles from ground level into and out of high building entrances. The ramps can be securely fastened to dock with pin locks. To avoid hang–ups with the vehicle, measure the under clearance and wheelbase of the vehicle being used. The ramps have a welded aluminum construction.

Manufacturer: Vestil, Manufacturer Part Number: SCR-72Uniform Capacity (lbs.): 15000 – The Heavy Duty Steel Container Ramp facilitates easy loading/unloading of shipping containers when placed on ground level. Hinged flip–over bridge allows for easy transportation and compact storage. Tapered lip provides smooth transition into container at various heights. Built in fork pockets in base for convenient fork truck positioning.

Manufacturer: Vestil, Manufacturer Part Number: VTR-7-14-12Uniform Capacity (lbs.): 5500, Working Height Minimum (in.): 32–1/2, Working Height Maximum (in.): 46, Usable Width (in.): 14, Curb Height (in.): 1–1/4 – The Aluminum Vehicle Twin Ramps provide a safe means for driving vans, pick–up trucks and some passenger vehicles from ground level into and out of high building entrances. The ramps can be securely fastened to dock with pin locks. To avoid hang–ups with the vehicle, measure the under clearance and wheelbase of the vehicle being used. The ramps have a welded aluminum construction.

Manufacturer: Vestil, Manufacturer Part Number: VTR-6-14-18Uniform Capacity (lbs.): 6000, Working Height Minimum (in.): 29, Working Height Maximum (in.): 41, Usable Width (in.): 14, Curb Height (in.): 1–1/4 – The Aluminum Vehicle Twin Ramps provide a safe means for driving vans, pick–up trucks and some passenger vehicles from ground level into and out of high building entrances. The ramps can be securely fastened to dock with pin locks. To avoid hang–ups with the vehicle, measure the under clearance and wheelbase of the vehicle being used. The ramps have a welded aluminum construction.

Manufacturer: Vestil, Manufacturer Part Number: VTR-5.5-14-24Uniform Capacity (lbs.): 6000, Working Height Minimum (in.): 22–1/2, Working Height Maximum (in.): 32, Usable Width (in.): 14, Curb Height (in.): 1–1/4 – The Aluminum Vehicle Twin Ramps provide a safe means for driving vans, pick–up trucks and some passenger vehicles from ground level into and out of high building entrances. The ramps can be securely fastened to dock with pin locks. To avoid hang–ups with the vehicle, measure the under clearance and wheelbase of the vehicle being used. The ramps have a welded aluminum construction.

Manufacturer: Vestil, Manufacturer Part Number: VTR-7-14-8Uniform Capacity (lbs.): 5500, Working Height Minimum (in.): 39, Working Height Maximum (in.): 55–1/2, Usable Width (in.): 14, Curb Height (in.): 1–1/4 – The Aluminum Vehicle Twin Ramps provide a safe means for driving vans, pick–up trucks and some passenger vehicles from ground level into and out of high building entrances. The ramps can be securely fastened to dock with pin locks. To avoid hang–ups with the vehicle, measure the under clearance and wheelbase of the vehicle being used. The ramps have a welded aluminum construction.

Manufacturer: Vestil, Manufacturer Part Number: VTR-5.5-14-16Uniform Capacity (lbs.): 5500, Working Height Minimum (in.): 16, Working Height Maximum (in.): 22–1/2, Usable Width (in.): 14, Curb Height (in.): 1–1/4 – The Aluminum Vehicle Twin Ramps provide a safe means for driving vans, pick–up trucks and some passenger vehicles from ground level into and out of high building entrances. The ramps can be securely fastened to dock with pin locks. To avoid hang–ups with the vehicle, measure the under clearance and wheelbase of the vehicle being used. The ramps have a welded aluminum construction.

Manufacturer: Vestil, Manufacturer Part Number: VTR-5.5-14-20Uniform Capacity (lbs.): 7000, Working Height Minimum (in.): 19, Working Height Maximum (in.): 27, Usable Width (in.): 14, Curb Height (in.): 1–1/4 – The Aluminum Vehicle Twin Ramps provide a safe means for driving vans, pick–up trucks and some passenger vehicles from ground level into and out of high building entrances. The ramps can be securely fastened to dock with pin locks. To avoid hang–ups with the vehicle, measure the under clearance and wheelbase of the vehicle being used. The ramps have a welded aluminum construction.

Manufacturer: Vestil, Manufacturer Part Number: VTR-5.5-14-10Uniform Capacity (lbs.): 7000, Working Height Minimum (in.): 12–1/2, Working Height Maximum (in.): 17–1/2, Usable Width (in.): 14, Curb Height (in.): 1–1/4 – The Aluminum Vehicle Twin Ramps provide a safe means for driving vans, pick–up trucks and some passenger vehicles from ground level into and out of high building entrances. The ramps can be securely fastened to dock with pin locks. To avoid hang–ups with the vehicle, measure the under clearance and wheelbase of the vehicle being used. The ramps have a welded aluminum construction.

Manufacturer: Eagle, Manufacturer Part Number: 1792KITAnchor Kit for Speed Bumps (6 Anchors & Adhesive)

Manufacturer: Wesco, Manufacturer Part Number: 150800Lightweight, portable ramp allows for easy movement up and down curbs. 600 lbs capacity. RAMP: YELLOW–GENERIC CURB. Plastic Construction. Weight Capacity: 600 lbs. A discount is available for purchases of 10 or more items. Call contractor at 317–867–2911 for details.

Manufacturer: Vestil, Manufacturer Part Number: RK-8The Wooden Ramp Kit allows building wooden ramps using common lumber. Each kit includes two (2) steel end plates and rubber bottom tips. Installation hardware is included. Drilling required for installation. Lumber/boards are not included. MFG Part# RK-8

Manufacturer: Vestil, Manufacturer Part Number: VCC-115-1Optional 115 Volt 1 Phase AC Power change for powered units.

Manufacturer: Vestil, Manufacturer Part Number: SB-HD-AK-4The Anchor Kits are a great addition to the facility maintenance department. The kit supplies a solution to securing speed bumps to a surface. The unit is designed of a strong construction that is resilient and long lasting throughout the harshest environments. Once the anchoring is in place, the speed bumps are ready for use. The kit is available in both glue down and asphalt anchor style. MFG Part# SB-HD-AK-4

Manufacturer: Vestil, Manufacturer Part Number: TS-20-6048Capacity: 20,000 lbs., Overall Size: 60"W x 48"L, Height Difference: 7" – Steel Truck Dockboard – Constructed of high strength (55,000 psi) steel for long life. Beveled edges on both ends permit smooth entry and exit. Deck is diamond plated for safe, efficient use. Welded safety curbs for maximum strength. Locking legs minimize ramp movement and are uneven to allow the dockboard to sit canted for easier floor pickup by forklifts. Standard with leverlift for quick portability with fork truck. Optional accessories: lifting chains, span locks, span pins/holes and removable pickup loops. Manufactured in compliance with OSHA.

Manufacturer: Vestil, Manufacturer Part Number: FRK-LVLDesigned to aid the fork lift driver in determining when the forks are level. Unit reduces the risk of damaging or piercing product when removing it from pallet racking. Fasten the steel leveler to the mast of the fork lift. While tilting the forks to the desired angle, the fork leveler will tilt as well, showing that the forks are not currently in a horizontal position. When forks are moved back into a safe level angle, the leveler will be perfectly horizontally.

Manufacturer: Vestil, Manufacturer Part Number: SSLSliding Span Locks for Aluminum Dockboards (BTA only).