vestil

Manufacturer: Vestil, Manufacturer Part Number: SS/75The Electric Hydraulic Dock Leveler Steel Shell is an ideal addition to the dock leveler. The steel shells are installed when the concrete is being poured, to provide steel panels on each vertical face of the pit, along with steel flanges along the top faces. Proper installation of a dockleveler requires the leveler to be welded along the upper rear edge of the pit, and the steel shells provide this edge. The steel shells include a front lower steel angle, that gets placed at the front bottom of the pit. This angle provides another essential location where the leveler needs to be welded to the pit. MFG Part# SS/75

Manufacturer: Vestil, Manufacturer Part Number: SS/76Optional steel shell for 84 (in.) by 72 (in.) pour in place installation.

Manufacturer: Vestil, Manufacturer Part Number: SS/78Optional steel shell for 84 (in.) by 96 (in.) pour in place installation.

Manufacturer: Vestil, Manufacturer Part Number : TSPIKE-39A spiked speed bump is an easy way to control the movement of traffic, while deterring vehicles from entering and exiting in the same lane. With a retractable spiked design, the speed bump allows traffic to flow only in a single direction. When the vehicle enters in the correct direction the spikes will submerge into the construction of the bump allowing the vehicle to pass unobstructed. If the vehicle were to exit using the same lane, the spikes will not retract but continue to stand tall. -Connectible to additional spiked speed bumps -Galvanized spikes -Crossable at a maximum of 5 MPH -Tires must pass over parallel to the spikes

Manufacturer: Vestil, Manufacturer Part Number : TSPIKE-ECAn end cap provides an effective finish to either side of the spiked speed bump. By fitting directly to an existing spiked speed bump, the previously open ends are shored up and contained. Caps are constructed of steel. -Sold in pairs -20 ton axle load capacity -Pre drilled mounting holes -Yellow powder coat finish

Manufacturer: Vestil, Manufacturer Part Number: WM-120Steel Square Safety Handrail bolted on Wire Mesh provides an economical way to protect people and machinery. Applications include loading docks, floor openings, walkways, and mezzanines.

Manufacturer: Vestil, Manufacturer Part Number: WM-48Steel Square Safety Handrail bolted on Wire Mesh provides an economical way to protect people and machinery. Applications include loading docks, floor openings, walkways, and mezzanines.

Manufacturer: Vestil, Manufacturer Part Number: WM-72Steel Square Safety Handrail bolted on Wire Mesh provides an economical way to protect people and machinery. Applications include loading docks, floor openings, walkways, and mezzanines.

Manufacturer: Vestil, Manufacturer Part Number: WM-96Steel Square Safety Handrail bolted on Wire Mesh provides an economical way to protect people and machinery. Applications include loading docks, floor openings, walkways, and mezzanines.

Manufacturer: Vestil, Manufacturer Part Number: S-GATE-60Steel Square Safety Handrail Sliding Gate.

Manufacturer: Vestil, Manufacturer Part Number: C-CONSteel Square Safety Handrails – Corner Connectors.

Manufacturer: Vestil, Manufacturer Part Number: SQ-CAP Steel Square Safety Handrail Black End Cap. ***MINIMUM ORDER QUANITY IS 15***

Manufacturer: Vestil, Manufacturer Part Number: M-BUMPSteel Square Safety Handrail Bumper (hardware included).

Manufacturer: Vestil, Manufacturer Part Number: ST-TRUCK-300The Steel Stair Hand Truck with unique design features tandem triple-wheel assemblies that work great when going up and down stairs. Wheel assembly smoothly rotates as you go up or down each step - eliminates the thud and bump associated with conventional two (2) wheel hand trucks on stairs. Rear wheel assembly also allows hand truck to roll easily on four (4) wheels while on flat surfaces. Single loop handle. MFG Part# ST-TRUCK-300

Manufacturer: Vestil, Manufacturer Part Number : VDKR-10-BP-TBWith well-being always at the forefront of everyone�s mind, a toe board is a natural addition to a safety railing. Through an extended height and length, the toe board maximizes pedestrian protection. Its simple design safeguards against falls and unnecessary injuries! -Pre-drilled mounting holes -Made of 0.1875" thick steel -Powder coat yellow finish -Rigid upright design

Manufacturer: Vestil, Manufacturer Part Number : VDKR-2-BP-TBWith well-being always at the forefront of everyone�s mind, a toe board is a natural addition to a safety railing. Through an extended height and length, the toe board maximizes pedestrian protection. Its simple design safeguards against falls and unnecessary injuries! -Pre-drilled mounting holes -Made of 0.1875" thick steel -Powder coat yellow finish -Rigid upright design

Manufacturer: Vestil, Manufacturer Part Number : VDKR-3-BP-TBWith well-being always at the forefront of everyone�s mind, a toe board is a natural addition to a safety railing. Through an extended height and length, the toe board maximizes pedestrian protection. Its simple design safeguards against falls and unnecessary injuries! -Pre-drilled mounting holes -Made of 0.1875" thick steel -Powder coat yellow finish -Rigid upright design

Manufacturer: Vestil, Manufacturer Part Number : VDKR-4-BP-TBWith well-being always at the forefront of everyone�s mind, a toe board is a natural addition to a safety railing. Through an extended height and length, the toe board maximizes pedestrian protection. Its simple design safeguards against falls and unnecessary injuries! -Pre-drilled mounting holes -Made of 0.1875" thick steel -Powder coat yellow finish -Rigid upright design

Manufacturer: Vestil, Manufacturer Part Number : VDKR-5-BP-TBWith well-being always at the forefront of everyone�s mind, a toe board is a natural addition to a safety railing. Through an extended height and length, the toe board maximizes pedestrian protection. Its simple design safeguards against falls and unnecessary injuries! -Pre-drilled mounting holes -Made of 0.1875" thick steel -Powder coat yellow finish -Rigid upright design

Manufacturer: Vestil, Manufacturer Part Number : VDKR-6-BP-TBWith well-being always at the forefront of everyone�s mind, a toe board is a natural addition to a safety railing. Through an extended height and length, the toe board maximizes pedestrian protection. Its simple design safeguards against falls and unnecessary injuries! -Pre-drilled mounting holes -Made of 0.1875" thick steel -Powder coat yellow finish -Rigid upright design

Manufacturer: Vestil, Manufacturer Part Number : VDKR-7-BP-TBWith well-being always at the forefront of everyone�s mind, a toe board is a natural addition to a safety railing. Through an extended height and length, the toe board maximizes pedestrian protection. Its simple design safeguards against falls and unnecessary injuries! -Pre-drilled mounting holes -Made of 0.1875" thick steel -Powder coat yellow finish -Rigid upright design

Manufacturer: Vestil, Manufacturer Part Number : VDKR-8-BP-TBWith well-being always at the forefront of everyone�s mind, a toe board is a natural addition to a safety railing. Through an extended height and length, the toe board maximizes pedestrian protection. Its simple design safeguards against falls and unnecessary injuries! -Pre-drilled mounting holes -Made of 0.1875" thick steel -Powder coat yellow finish -Rigid upright design

Manufacturer: Vestil, Manufacturer Part Number: TAL-220-DCThe Tote-A-Load is designed to lift open bottom skids, boxes, and baskets. The battery operated lift is ideal for positioning products at workstation heights for increased productivity. The up/down lever control is conveniently located on the power unit. The DC power unit includes on-board charger. Polyurethane swivel casters with brake are standard. -Designed to lift open bottom skids, boxes, and baskets -Position products at work heights for increased productivity -Up/down lever control is conveniently located -DC power unit includes on-board charger

Manufacturer: Vestil, Manufacturer Part Number: TAL-260-DCThe Tote-A-Load is designed to lift open bottom skids, boxes, and baskets. The battery operated lift is ideal for positioning products at workstation heights for increased productivity. The up/down lever control is conveniently located on the power unit. The DC power unit includes on-board charger. Polyurethane swivel casters with brake are standard. -Designed to lift open bottom skids, boxes, and baskets -Position products at work heights for increased productivity -Up/down lever control is conveniently located -DC power unit includes on-board charger